INSTALLATION GUIDE

Below are the full fitting instructions for your new gate

Driveway Gates

With aluminium posts

Preparation:

Measuring widths and heights

PLEASE NOTE: These installation instructions are relevant to ALL Full Privacy and Partial Privacy Driveway Gates.

Step 1

Measure and secure your aluminium posts either by concreting these into the ground or fixing them with the bolts (which are included) into a solid surface.

Step 2

Start with the bottom hinge first. Place floor mounted hinge in location on a solid surface floor at your intended measurement to your post. Mark the fixing positions on the surface floor, drill through enough for the bolt size and then secure your floor mounted hinge in place with bolts provided.

(If your driveway gates are accommodating any ground automation, please skip to step 3 after automation has been installed).

Step 3

Place one of your driveway gates on top of the bottom-mounted hinge or ground automation. Level the driveway gate to mark the fixing position for the top adjustable mounted hinge.

Step 4

Drill pilot holes into post, then secure your wall mounted hinge with bolts provided.

Step 5

Repeat above steps for the other side of your driveway gate, making sure your measurements and levels are correct.

Step 6

Once both gates are installed, you can now adjust your margins either side of your gate to level your gates and increase or decrease any gaps.

Step 7

Handle set (optional)

Your driveway gate handle set will come pre-drilled and fixed for you. If you change the gates around, you may need to switch the handle over. Unscrew the handle and turn it 180 degrees; ensure your handles are in place properly with the screw side facing inwards towards your property.

Gate stop (optional)

Close your driveway gates level. Mark the fixing positions on the surface floor, drill pilot holes enough for the bolt size and then secure your gate with bolts provided.

Driveway Gates

Without aluminium posts

Preparation:

Measuring widths and heights

PLEASE NOTE: These installation instructions are relevant to ALL Full Privacy and Partial Privacy Driveway Gates.

Step 1

Start with the bottom hinge first. Place wall mounted hinge in location and mark the fixing positions, allowing 50mm from surface of floor to tighten fixing. Drill pilot holes enough for the bolt size and then secure your floor mounted hinge in place with bolts provided.

(If your driveway gates are accommodating any ground automation, please skip to step 2 after automation has been installed).

Step 2

Place one of your driveway gates on top of bottom mounted hinge or ground automation. Level the driveway gate to mark the fixing position for the top adjustable mounted hinge.

Step 3

Drill pilot holes into pillar, then secure your wall mounted hinge with bolts provided.

Step 4

Repeat above steps now for the other side driveway gate, making sure your measurements and levels are correct.

Step 5

Once both gates are installed, you can now adjust your margins either side of your gate to level your gates and increase or decrease any gaps.

Step 6

Handle set (optional)

Your driveway gate handle set will come predrilled and fixed for you. If you change the gates round you may need to switch the handle over. Unscrew the handle and turn it 180 degrees; ensure your handles are in place properly with the screw side facing inwards towards your property.

Gate stop (optional)

Close your driveway gates level. Mark the fixing positions on the surface floor, drill through enough for the bolt size and then secure your gate with bolts provided.

Driveway Gates

Fitted inside existing brickwork

Preparation:

Measuring widths and heights

PLEASE NOTE: These installation instructions are relevant to ALL Full Privacy and Partial Privacy Driveway Gates.

Step 1

Start with the bottom hinge first. Place wall mounted hinge in location and mark the fixing positions, allowing 50mm from surface of floor to tighten fixing. Drill pilot holes enough for the bolt size and then secure your floor mounted hinge in place with bolts provided.

(If your driveway gates are accommodating any ground automation, please skip to step 2 after automation has been installed).

Step 2

Place one of your driveway gates on top of bottom mounted hinge or ground automation. Level the driveway gate to mark the fixing position for the top adjustable mounted hinge.

Step 3

Drill pilot holes into pillar, then secure your wall mounted hinge with bolts provided.

Step 4

Repeat above steps now for the other side driveway gate, making sure your measurements and levels are correct.

Step 5

Once both gates are installed, you can now adjust your margins either side of your gate to level your gates and increase or decrease any gaps.

Step 6

Handle set (optional)

Your driveway gate handle set will come predrilled and fixed for you. If you change the gates round you may need to switch the handle over. Unscrew the handle and turn it 180 degrees; ensure your handles are in place properly with the screw side facing inwards towards your property.

Gate stop (optional)

Close your driveway gates level. Mark the fixing positions on the surface floor, drill through enough for the bolt size and then secure your gate with bolts provided.

Driveway Gate Installation Video

Fitting your aluminium gate is quick and easy

Garden Gates

With aluminium posts

Preparation:

Measuring widths and heights

PLEASE NOTE: These installation instructions are relevant to ALL Full Privacy and Partial Privacy Garden Gates.

Step 1

Measure and secure your aluminium posts either by concreting these into the ground or fixing them with the bolts (which are included) into a solid surface.

Step 2

Start with the bottom hinge first. Place floor mounted hinge in location on a solid surface floor at your intended measurement to your post. Mark the fixing positions on the surface floor, drill through enough for the bolt size and then secure your floor mounted hinge in place with bolts provided.

Step 3

Place the garden gate on top of the bottom-mounted hinge. Level the garden gate to repeat marking the fixing position for the top wall mounted hinge.

Step 4

Drill pilot holes into post, then secure your wall mounted hinge with bolts provided.

Step 5

Once garden gate is hung, you can now adjust your margins of your gate to increase or decrease any gaps.

Step 6

Allowing 20mm gap for the lock keep. Level garden gate in closed position then place lock keep and mark the top for fixing positions. Drill pilot holes into post. Place lock keep in position and screw into position with fixings provided.

Step 7

If you change the gates round you may need to switch the handle over. Unscrew the handle and turn it 180 degrees; ensure your handle is in place properly with the screw side facing inwards towards your property.

Garden Gates

Without aluminium posts

Preparation:

Measuring widths and heights

PLEASE NOTE: These installation instructions are relevant to ALL Full Privacy and Partial Privacy Garden Gates.

Step 1

Start with the bottom hinge first. Place wall mounted hinge in location and mark the fixing positions, allowing 50mm from surface of floor to tighten fixing. Drill pilot holes enough for the bolt size and then secure your floor mounted hinge in place with bolts provided.

Step 2

Place the garden gate on top of bottom mounted hinge. Level the garden gate so you can repeat marking the fixing position for the top wall mounted hinge.

Step 3

Drill pilot holes into pillar, then secure your wall mounted hinge with bolts provided.

Step 4

Once garden gate is hung, you can now adjust your margins of your gate to increase or decrease any gaps.

Step 5

Allowing 20mm gap for the lock keep. Level garden gate in closed position then place lock keep and mark the top for fixing positions. Drill pilot holes into post. Place lock keep in position and screw into position with fixings provided.

Step 6

If you change the gates round you may need to switch the handle over. Unscrew the handle and turn it 180 degrees; ensure your handle is in place properly with the screw side facing inwards towards your property.

Garden Gate Installation Video

Fitting your aluminium gate is quick and easy

Ornate Gates

Without aluminium posts

Preparation:

Measuring widths and heights

PLEASE NOTE: These installation instructions are relevant to ALL Ornate Gates.

Step 1

Start with the bottom hinge first. Place wall mounted hinge in location and mark the fixing positions. Drill pilot holes enough for the bolt size and then secure your ornate wall mounted hinge in place with bolts provided.

(If your driveway gates are accommodating any ground automation, please skip to step 2 after automation has been installed).

Step 2

Place one of your driveway gates on top of the bottom ornate wall mounted hinge or ground automation. Level the driveway gate to mark the fixing position for the top ornate wall mounted hinge.

Step 3

Drill pilot holes into pillar, then secure your ornate wall mounted hinge with bolts provided.

Step 4

Repeat above steps for the other side of your driveway gate, making sure your measurements and levels are correct.

Step 5

Once both gates are installed, close your driveway gates level. Mark the fixing positions on the surface floor, drill through enough for the bolt size and then secure your gate with bolts provided.

 

** Installing gate drop bolts onto these gates is recommended (we do not currently stock these).

** Gate handle set and lock are unable to be installed on Ornate Gates.

Ornate Gates

Fitted inside existing brickwork

Preparation:

Measuring widths and heights

PLEASE NOTE: These installation instructions are relevant to ALL Ornate Gates.

Step 1

Start with the bottom hinge first. Place wall mounted hinge in location and mark the fixing positions. Drill pilot holes enough for the bolt size and then secure your ornate wall mounted hinge in place with bolts provided.

(If your driveway gates are accommodating any ground automation, please skip to step 2 after automation has been installed).

Step 2

Place one of your driveway gates on top of the bottom ornate wall mounted hinge or ground automation. Level the driveway gate to mark the fixing position for the top ornate wall mounted hinge.

Step 3

Drill pilot holes into pillar, then secure your ornate wall mounted hinge with bolts provided.

Step 4

Repeat above steps for the other side of your driveway gate, making sure your measurements and levels are correct.

Step 5

Once both gates are installed, close your driveway gates level. Mark the fixing positions on the surface floor, drill through enough for the bolt size and then secure your gate with bolts provided.

 

** Installing gate drop bolts onto these gates is recommended (we do not currently stock these).

** Gate handle set and lock are unable to be installed on Ornate Gates.